How To Adjust Water Softener Settings

H2o Softener Settings
Guide to Water Softener Controls, Adjustments & Maintenance

• Post a QUESTION or COMMENT well-nigh water softener controls, adjustments, timers, common salt dose setting, regeneration frequency setting

InspectAPedia tolerates no conflicts of interest. We accept no relationship with advertisers, products, or services discussed at this website.

Water Softener Operating & Maintenance Instructions:

How to set & adjust a water softener or water conditioner.

Here we provide an possessor'southward guide to h2o softener controls, what they are, what they do, how to set up them - for water softener or water conditioner maintenance, including water softener adjustment of the regeneration or backwash cycle frequency and the water softener salt dose.

We explain the salt dose, regen bicycle, hardness setting, and brine tank float level adjustment. We also discuss setting the water softener timer or clock.

Nosotros also provide an Article Alphabetize for this topic, or you tin try the folio top or bottom SEARCH BOX equally a quick way to find information you need.

Homeowner's Guide to Water Softener Settings & Adjustments - how to set the water softener controls

How to set the softener regeneration cycle frequency. Recommended h2o softener settings if you don't have other data; Common salt dose tabular array for water conditioners; salt punch setting process.

How to calculate the required common salt dose; how to adjust the brine tank float; how to set the water softener clock; how to set electronic controls on a water softener.

Click to enlarge any epitome or table]

Article Serial Contents

• H2o SOFTENER Aligning & CONTROLS
  • 4 Bones Water SOFTENER ADJUSTMENTS
  • vi WATER SOFTENER CONTROL SETTING DETAILS
  • RECOMMENDED SETTINGS for H2o SOFTENERS
  • H2o SOFTENER CAPACITY SETTING
  • WATER SOFTENER CLOCK SETTINGS
  • Water SOFTENER ELECTRONIC CONTROL SETTINGS
  • H2o SOFTENER SALT DOSE SETTING
  • WATER SOFTENER Manual REGENERATION
  • WATER SOFTENER REGENERATION Bicycle Elapsing
  • H2o SOFTENER REGENERATION Wheel FREQUENCY
  • H2o SOFTENER MANUAL REGENERATION
• WATER CONDITIONER / SOFTENER MANUALS
• H2o SOFTENER RESIN REPLACEMENT

Four Bones Adjustments or Tasks Necessary to Utilise a H2o Softener

Because the hardness and volume of water used both vary from one edifice to another, a water softener or water conditioner includes controls that let the installer or edifice occupants to suit the system to work properly.

Water conditioner or water softener controls typically include either analog-type dials with pins, buttons, or levers (control at left)( or electronic controls operated by pushbuttons (discussed subsequently in this article

at ELECTRONIC WATER SOFTENER CONTROLS).

The two master adjustments on whatsoever water softener, whether they are washed manually past an owner or automagically by water hardness sensors, are listed beneath, followed by ii basic maintenance chores.

1. Set the Regen or Backwash Frequency: The frequency of water conditioner regeneration cycle or the "backwash" wheel.

   See Water SOFTENER REGENERATION Cycle FREQUENCY for details

2. Set the Salt Dose: The amount of common salt (or salty water) that must exist run through the water conditioner during each regeneration bike or "backwash" cycle.

   See H2o SOFTENER Salt DOSE SETTING for details.

3. Add salt: considering a water conditioner (or water softener) consumes salt during each regeneration or backwash wheel, you will demand to buy and add salt to the brine tank from time to time. You can determine when to add common salt by visual inspection - salt gets low inside the brine tank, or you can if you prefer hire a h2o softener maintenance visitor who will deliver and install the salt for you.
4. Make clean the H2o Conditioner:

   As we explain at Water SOFTENER CLEANING & SANITIZING, water softener alkali tanks as well need to exist emptied and cleaned from time to time.

   Sanitizing the water softener will require a regeneration cycle to be complete.

   See Water SOFTENER Manual REGENERATION

Question: how to use the pins and punch in the photograph above?

[Shown just higher up is ] exactly the control my softener has, simply I cannot discover instructions on how to set the pins on the dial that say 2 minutes per pin, or get repair parts.

My softener is an NPS AquAmerica Model 92083. Mfgr is/was in Norton, Ohio and was fabricated in about 1995.

Can you help please? - Anonymous by private email 2022/01/22

Reply:

That dial is decision-making the regen cycle duration - a way of adjusting the softener to accord with the hardness of your water. You'd move the pins to a college number to obtain a longer regen time if the h2o remains difficult after treatment - and presuming all else is working commonly.

I attach a water softener transmission [PDF document] that may non be an exact match only should be helpful. Plant at Aqua Systems 800 n447 5582 http://world wide web.ilovemywater.com/Contact-Aqua-Systems.aspx

Clock Settings for a Water Softener

How to Fix the Water Softener Clock & Regeneration Bicycle Frequency

Because water conditioners and their controls vary amidst manufacturers and models, below we discuss several methods for determining and really making the necessary settings or adjustments on this equipment.

And there is a third maintenance task for building owners who have a water conditioner: setting the clock

Guide to Setting the water softener controls:

Our photo to a higher place shows the standard controls on a water softener, permitting the user to specify the days on which a recharge/backwash bike volition occur, the salt dose, and also the time of day.

Set the water softener clock:

Setting the clock on the water softener command is important for two reasons: starting time, you won't exist bothered by hearing it run if information technology recycles when you are asleep or out of the home, and second, since the water softener recharge wheel uses plenty of water, it'south a skillful idea to transport that discharge to the septic system at a time when other plumbing fixtures are not in use - thus spreading the wastewater load on the septic system out over a longer period.

Set the clock dial to the authentic time of twenty-four hour period and ready the water softener regeneration time to an hour when the building occupants are least likely to be using water, such as at 2AM - the standard factory pre-set regeneration hour.

On units with a clock dial, the silvery colored section corresponds to daytime hours and the black colored portion corresponds to night fourth dimension hours.

Normally the "clock dial" is adapted past lifting it upwardly and turning it to the proper position, or turning a dial to line upwards the right hour of the twenty-four hour period with an indicator arrow (lower correct in our photo).

Question: Where is the "Clock" on my h2o softener and how do I prepare it?

Extremely well written and done !! Thank you. But, i however tin not identify my softener system or control clock. It was hither when i bought the house. Is at that place anywhere some pictures identifying unlike controllers. bugrubert@hotmail.com

Answer:

Bugrubert, yous are welcome to send me photos of the equipment and all labels you tin find including inside the command cover - utilize the email accost found at the CONTACT link shown at the summit, left, and lesser of all of our web pages.

On dial type (non LED or LCD type display) h2o softeners or conditioners, you may non see a dial that looks like a clock with easily. In the water conditioner command photos below, from left to right,

• The clock on this h2o conditioner control is set past turning the knob marked "Time of Day" that has numbers on it then that the electric current AM or PM hour is opposite the pointer indicate (lower right corner of our first photo at beneath left).

  You lot volition come across a similar "Time Set" button on Autotrol water conditioners.

• The clock on the next water conditioner control (below right) is ready by turning the AM (white surface area) or PM (black area) hr to be contrary the black arrow to which our red arrow is pointing.

• On an electronic display water softener such equally the Autotrol 460i, for example, to set up the time of day you may have to set a jumper side by side to the word "Time" on the command (bluish arrow) and and so push the "Time Ready" push button (red arrow) until the correct AM and PM time of day is indicated on an LED brandish.

Water Softener Control Adjustment Procedure Details - 6 Like shooting fish in a barrel Steps to Soft Water

1. Measure the hardness of your h2o

   using a test kit or by asking a service tech to do it for you.

   The number you go should be expressed in either GPG (grains of hardness per gallon of water) or in PPM (parts per million of minerals in your water)

   Our photograph (left) illustrates a unproblematic water hardness test that as well measures other water parameters.

2. Accommodate the water softener "Hardness" setting.

   Adjust the h2o softener "hardness" to the same number as the hardness that you measured for your own water supply. For example if you measured your water hardness as xxx grains per gallon (xxx GPG), then the "hardness" setting volition be "xxx". If your water hardness was measured in parts per one thousand thousand (PPM),

   Separate PPM by 17.ane to get hardness in grains per gallon: PPM / 17.1 = GPG

   Or to convert from hardness in PPM to hardness in grains per gallon,

   Multiply grains per gallon GPG by 17.1 to get hardness in PPM: GPG x 17.1 = PPM

3. Ready the water softener "Capacity":

   Accommodate the water softener capacity setting according to your manual and our example discussed earlier.

   Typically chapters for a water softener is a number from 1 to 99 kilograins. This is the corporeality of hardness, measured in grains, that the softener tin remove before it needs to be re-generated.

   Suppose your water conditioner chapters setting is adjusted to xxx kilograins (1st column at left side of the table salt dose able)

   More details are

   at H2o SOFTENER CAPACITY SETTING

4. Determine softener treatment tank size:

   Let's assume your water softener handling tank is a one-cubic foot capacity unit. Notice the tabular array column nether 1.0 Ft³. (4th column from left in the water softener salt dose table). The water softener tank size is it'southward resin volume in cubic anxiety, typically a number between 0.75 cu ft and 2.0 cu ft.

5. Read the recommended salt dose in pounds:

   reading across from xxx kilograins of hardness in cavalcade 1 to our fourth column (the one cubic pes softener size) we run into that the manufacturer recommends 15 pounds of salt.

6. Prepare the salt dose - the brine control:

   gear up the dial to 15 pounds of common salt. If your equipment is in the U.K., Australia, New Zealand, Canada, or another country that measures and marks equipment using the metric arrangement your salt dose will be measured in kilograms or kg of salt.

   If you demand to convert pounds to kilograms or kg, divide pounds past ii.2. More examples of how to decide and set the h2o softener salt dose can be read

   at
   RECOMMENDED SETTINGS for Water SOFTENERS

Sentry out: follow the instructions in the right maintenance manual for your own equipment. And in the salt dose table, don't confuse kg of salt (numbers in the table body) with kilograins of water hardness (numbers in table column 1).

Also, remember this setting is adjusting only the salt dose, not the frequency of regeneration cycle.

Another Approach to Water Conditioner Settings for Salt Dose & Regeneration Frequency

If you don't have a manual and can't find instructions for your unit, (and don't want to call a qualified service technician) leave the salt dose alone, and so send the softener through a regeneration bike and measure the hardness of your water again.

So monitor water hardness on the days betwixt your regen cycle and the next automatic regen bike, during a menstruum of your best estimate at boilerplate water quantity use. If your water shows unacceptable hardness before another softener regen, you'll need to increase the frequency of regeneration cycle.

Typical frequencies for manually-set water softener regeneration as a starting point are are once a week, in one case every three or four days, every other day, and daily.

If you lot are running the system daily and water is still too hard you may demand to increase the common salt dose. But don't overdo the salt or you lot may accept salty water - a health and artful issue.

Subjective judgment of water hardness:

It's all-time to measure out the hardness of your water - kits are inexpensive or some services will perform the test at no charge.

If you lot can't get a lather using shampoo on your head in the shower, either you lot're bald, or the water is nevertheless pretty difficult. If your h2o feels slimy and y'all take trouble rinsing off lather, your water might be more soft than necessary (though other problems can also crusade this symptom).

Water Softener or Water Equipment Adjustment Tip:

Most water treatment companies will be glad to transport a representative to your building to test water hardness (or other contaminants) and to suggest you lot on the condition and settings of the h2o treatment equipment you have in identify, or to suggest alternatives if you are shopping.

Regeneration Bicycle Frequency on H2o Softeners

How Frequently does the Water Softener Demand to Run a Aftermath & Regeneration or "Recharge" Bike?

Your water softener manufacturer will provide a Salt Dosage/Frequency Nautical chart along with the softener's installation and maintenance instructions.

A h2o softener recharge frequency and common salt dose example is provided past Culligan:,

"If four individuals alive in the household, and the water has a total hardness of 18 grains per gallon, the salt dosage per recharge for the h2o conditioner will be 5 pounds (2.five kg) and the recharge frequency will be iii (or every 2 days). Monthly table salt usage tin can exist estimated, using these figures, at about 75 pounds (37.5 kg).

IBC in Australia provides this elementary formula that can summate the regeneration cycle for a water softener if y'all know all of the required parameters:

Number of Days Between Water Softener Regeneration Cycles = Due north

Maximum capacity of the treatment tank in grams of CaCO3 or NaCL = C

Volume of water passing through the treatment tank per mean solar day = Q (Kiloliters per day) or (Gallons per day)

Hardness of the incoming water measured in micrograms/Liter (mg/L) or in PPM = H

Northward = C / (H x Q)

This should be taken only as a rough calculation - ready your aftermath frequency to this number of days or less.

An extra regeneration cycle is needed under some circumstances.

Details are at WATER SOFTENER Transmission REGENERATION.

Water softener regeneration cycle frequency vs. wheel duration fourth dimension

Above we discussed the frequency of water softener regeneration cycles: how ofttimes the equipment should run through a regeneration bicycle.

Frequency of water softner regeneration is non the same question as duration of the regeneration cycle.

See Water SOFTENER RUNS TOO LONG for a discussion of abnormally-long h2o softener regeneration bike time elapsing.

Recommended Settings for Water Softeners

So What Settings Should I Use on My H2o Softener? How to Prepare the H2o Softener Table salt Dose

Question: What salt dose should I apply on my water softener?

I have a Autotrol 460i water softer. The water hardness going into my firm measures ten. What settings do I need set in order to create h2o hardness setting out of my faucets to read around 1or ii? - Walter Schwartz

Reply: The salt dose for your water conditioner depends on some variables. Hither is an example and a water softener salt dose table for reference

Some water conditioners (h2o softeners) automagically rail water quantity usage and h2o hardness and adjust themselves without you having to do a thing. Simply lots of models require a transmission adjustment based on water hardness and water quantity used.

The necessary h2o softener settings depend not just on water hardness just on your brand and model of h2o softener equipment and how much water you are using. Here are some remarks about setting the salt dose and regen frequency on a water softener:

Most h2o softener owners manuals include a tabular array of recommended settings. Outset in that location. If you don't accept an owner'southward manual telephone call the manufacturer's tech service and give them the model number and ask for a manual also as their setting advice.

Water Softener "Hardness Setting"

Here is an excerpt from a copy of the manual for

your AUTOTROL Water Conditioning Control System, Installation, Operation, and Maintenance Manual. [PDF]

On this water conditioner you can specify the time of regeneration (factory is prepare to 2:00 AM) to exist sure it's running at a time when you are non using water in the building.

Here are instructions on adjusting the hardness setting for this equipment: [Quoting]

H2o Conditioner Hardness Setting: Motion the jumper to the ready of pins next to the discussion HARDNESS (Figure xi).

Press the black Fourth dimension SET push button until the correct hardness is displayed.

The hardness range is from i to 99 grains per gallon.

To change water hardness stated in parts per 1000000 (PPM) to grains per gallon (GPG) use this formula:

Parts per Million / 17.1 = Grains per Gallon

Question: tin I turn off my water softener

2021/04/fourteen

My water softener hardness was set at 197 I have metropolis water hardness 6 I dont want information technology to soft pentair 255/760

Moderator answer: Explain the "Hardness setting number" on a water softener command head

@Anonymous,

If yous don't already have it, you tin find the transmission for your Pentair water softener at

at H2o CONDITIONER / SOFTENER MANUALS inspectapedia.com/plumbing/Water_Softener_Manuals.php#P

I have to refer to the manual considering the hardness setting (or common salt-dose) procedure varies among softener brands and models.

You might also review the water usage rate in your home every bit that might allow y'all reduce the frequency of softener regeneration.

Finally: let's exist certain we've got the numbers correct. If your softener is non needed at all then you could simply put the softener in bypass style.

Permit's recap the math:

How to o convert between grains of hardness (GPG) or "Grains of Hardness per Gallon of Water" and mg/L or micrograms (of calcium & magnesium) per liter of water we

• Divide mg/L by 17.ii to become GPG
• Multiply GPG ten 17.two to become mg/50

And then if your water hardness is measured at vi GPG that's 103.2 mg/L

0 to 60 mg/L (milligrams per liter) equally calcium carbonate is classified every bit soft.

So your water is rather difficult - IF that number "vi" is GPG.

If y'all bypass the water softener yous risk scale-clogged water heater and pipes.

Let's likewise review that 197 setting on your Pentair water softener to be sure that'south a GPG setting - it might instead be a mg/50 setting and and so not so far off from correct as you may think.

Water Softener / Conditioner Capacity Setting

Typically the capacity for a water softener - the amount of hardness it tin can remove earlier a regeneration is necessary - is a number from 1 to 99 kilograins.

Suppose your h2o conditioner capacity setting is adjusted to 30 kilograins (1st cavalcade at left side of the salt dose able)

For our example water softener, movement the jumper to the set of pins adjacent to the word CAPACITY (Effigy 12).

Press the black TIME Ready push button until the correct capacity value is displayed. The chapters range is 1 to 99 kilograins.

Refer to the Suggested Salt Dial Settings table [shown below].

Return the jumper to the top prepare of pins next to the give-and-take TIME and replace the access door.

The next 3 sets of pins are used for manufacturing plant testing and are not used in normal operation. The jumper must NOT exist left on any pins other than the top pair next to the word Time. Otherwise, the unit may not function.

Note: A spare jumper is located on the bottom gear up of pins.

In the upshot that the hardness or capacity setting must exist changed, but follow the appropriate steps described above.

Note: We have tried to translate these mysterious and unclear instructions into understandable English,

at Water Softener Control Aligning Procedure Details

so CONTACT united states of america with suggestions.

Like some other advanced water conditioners on the market, the control module for the Autotrol water softener includes a microprocessor that monitors your level of water usage, adjusting the regeneration cycle accordingly.

See WATER SOFTENER RESIN PROPERTIES & SOURCES for a detailed caption of the human relationship between incoming h2o hardness (in grains), water usage book, h2o softener resin properties, and the capacity of the water softener to remove hardness.

How to Set the Water Softener Salt Dosage

Consummate details about adjusting the h2o softener salt dose are found in these separate explanations:

• WATER SOFTENER Table salt DOSE SETTING
  • WATER SOFTENER SALT DOSE Table
  • H2o SOFTENER Salt DIAL SETTING
• WALTER SOFTENER Table salt DOSE CALCULATION
• WATER SOFTENER Alkali TANK Bladder LEVEL ADJUSTMENT

Excerpts summarizing h2o softener common salt utilize are only below.

Water softener brine command or salt dose and regeneration cycle frequency as well as other settings vary depending on the type of water softener control on your motorcar. Just the bones concept remains the same:

• The harder your incoming water supply is, the larger is the salt dose that will be needed to regenerate the water softener itself.
• The larger the h2o quantity yous use in your home, the more oftentimes the water softener volition need to run through a regeneration cycle.

• The Brine Control: how to set the water softener salt dose:

  Your water softener's instructions (available from the manufacturer or from a local h2o softener service company) volition tell yous what common salt dosage to prepare on the softener as a function of how many grains of hardness your water supply shows.

  The salt dose scale on a typical water softener indicates the number of pounds of salt to be used in each h2o softener recharge bicycle.

  Shown at left, the pointer knob is set to between 14 and fifteen pounds of salt on an Autotrol salt dose control (a loftier setting past the fashion).

[Click to overstate whatsoever image]

Set the water softener recharge frequency: your h2o softener's instructions will tell yous how ofttimes the arrangement should be recharged as a function of your estimated daily h2o usage in gallons.

At left is a typical water softener recharge frequency chart for a Culligan Arrangement 19 or 23 Water Conditioner.

[Click to enlarge any image or table]

Typically a water softener control includes a vii-day recharge frequency dial with tabs that can be pushed-in or pulled out to cause the water softener to use a recharge cycle on that day. Harder water and higher quantity of h2o usage means more frequent recharge cycling is needed.

If your water softener has an automatic sensor of the hardness of water leaving the handling tank (such as the Culligan Soft-Minder®), it tin decide for itself when a recharge or regeneration bicycle is needed.

Water Softener Electronic Command Setting Process

Question: How practise I set the Water Softener Controls on a Sears Kenmore Electronic Unit of measurement?

My water conditioner is a Kenmore model that uses an electronic control rather than dials, levers and pins. How do I set that control?

Answer:

To gear up a Kenmore water conditioner electronic control endeavour these bones steps. If these instructions don't match your unit contact united states by email with your make and model number and we'll assistance you find those instructions. [eighteen]

1. Select button:

   Detect the Hardness Setting by pressing the Select Button on your h2o conditioner control box until you see the command display flash the word Hardness and a number. The number is the current hardness setting of your equipment.

2. Choose the command setting number :

   The default setting on a typical Kenmore water softener with this control blazon is 25. The electronic control setting number to which y'all should set the electronic control on your water conditioner is either

   1. Grains per gallon of hardness (if your arrangement does non include an iron treatment component)

      or

   
   
   2. Control Setting Number calculated as follows:

      For a typical Kenmore water conditioner instructions indicate

      Hardness Number = GPG of hardness (grains per gallon of hardness)

      Atomic number 26 Number = Iron ppm x 5

      Control setting = Hardness Number + Iron Number

      If you don't know what hardness number you lot want, come across our give-and-take nearly hardness numbers in the article above or use the test kits we describe to determine the hardness of your h2o supply. For Kenmore customers Sears offers a free water hardness and h2o iron exam.

3. Arrow Push:

   printing the Up or Downward buttons to modify the current Control Setting Number to the setting you want

   To continue with other settings on this type of machine,

4. Select push:

   printing the Select Button again to show Recharge Fourth dimension

5. Cull the Recharge Time of Day:

   this setting determines the time of day at which the system volition run through a regeneration bike. The factory default is ii:00 AM - which we recommend unless you are often using building water at that hour. Use the up or down arrows to change the recharge time in one-hour increments.

   To go along with other settings on this type of machine,

6. Select Button:

   press the Select button over again to evidence Set Table salt Level

7. Choose the Current Brine Tank Salt Level:

   open the brine tank, note the yellow sticker that has numbers 0-8 imprinted on it. Choose the common salt level to match the highest number on the decal to which the salt is actually present in the brine tank.

   This setting tells the water softener how much salt is in the brine tank and thus will allow the equipment to tell you (on its display) when the salt level is low - when you lot need to add more common salt to the system.

8. Select Push: use the Select Button once again to cease up

   setting the Kenmore water softener control past pressing it again to prove the current time of day.

9. Set the water softener clock to right fourth dimension of day:

   if the clock is non displaying the correct time, you can also utilize the Select Push to choose Set Time of Day, then gear up the correct time using the up and down buttons.

As we particular

at Observe Hard H2o

information technology'south easy to see if your h2o softener is doing anything past using one of several water hardness tests including the strips shown at left. Or you may suspect a problem if you are no longer able to get your shampoo to lather when taking a shower.

Reader Q&A - also see the FAQs series linked-to below

Jim

That'south probably a common controller on many softeners; try taking a look at the steps given at

IDENTIFY Water SOFTENER BRAND / MODEL

Yous tin can also post a photo of any other stickers or tags on or in the control; often from something every bit indirect as a patent no. we (or you) can use Google Scholar to find the company of origin.

I am trying to ID what make this controller is. I have no other info on it. Looking for a transmission .
Thanks.
.

Jeff

Distressing that at that place seems to be a misunderstanding, but yous did not purchase parts for your h2o softener from united states. (InspectApedia.com)

We practice non sell annihilation and never accept: no parts, no services, nothing.

InspectAPedia is an contained publisher of edifice, environmental, and forensic inspection, diagnosis, and repair data for the public - we have no business nor financial connection with any manufacturer or service provider discussed at our website. We very much welcome critique, questions, or content suggestions for our web articles. Website content contributors, fifty-fifty if it'southward only a pocket-size correction, are cited, quoted, and linked-to from the appropriate additional web pages and manufactures - which benefits us both. Working together and exchanging information makes united states of america amend informed than any individual can exist working alone.

More than about us is at Most InspectApedia.com inspectapedia.com/Admin/About_InspectApedia.php

The recommended regen frequency settings for your water softener depend on both the hardness (you cite 17 grains) and besides on the water softener make and model.

That'southward because water softener capacity varies among brands and models.

However it should be pretty easy to answer your question: take a wait in the manual for your particular water softener. You'll notice a table of recommended salt dose and regen frequency settings for your water hardness for your specific model.

Or in the article above on this very folio, please take a await at

iv Basic H2o SOFTENER ADJUSTMENTS

and

6 Water SOFTENER CONTROL SETTING DETAILS

and don't hesitate to enquire follow-upward questions if any of that is unclear.

Cheers for asking.

I recently purchased parts from you to rebuild my softener and information technology is working like a champ now. My water is 17 grains hard (untreated) and there are two of united states in the house. Nosotros occasionally take 2 extras when a kid comes dwelling for the weekend. What would y'all suggest for regeneration settings?
Cheers

Certain Todd

Let's first past taking a await at the suggestions at Identify H2o SOFTENER BRAND / MODEL

https://inspectapedia.com/plumbing/Water-Softener-Identification.php

Hi, Trying to find out what softener this is. Hoping to track down a transmission or instructions on how to properly set this water softener. It's an older unit, installed @ 2003. Information technology is working, simply don't know how to really anything on it. Actually capeesh any one who tin can help out!!

Thanks!

Sounds like a lot to me. Check the settings on the h2o softener; often the softener volition give an actual salt "dose" in pounds. Yous tin compare that with the pounds (or book) of salt in the brine tank.

Also tell us the level of hardness in your water and see what your softener manual says should be the salt dose setting or that hardness.

my softener used 1 40# bag of salt for ane regen wheel. is this normal?

Lee

The meaning of an mistake lite on a water softener is make and model dependent then I'yard afraid you lot demand to consult the manual to run into what the area code is.

Lite not finish blinking

...

Go on reading at WATER SOFTENER CONTROLS & Functioning - topic home, or select a topic from the closely-related manufactures beneath, or run across the complete ARTICLE Alphabetize.

Or see H2o SOFTENER Command SETTING FAQs - questions & answers about water softener control settings posted originally at this commodity

Or see these

Recommended Manufactures

• WATER SOFTENERS & CONDITIONERS - abode
• DIAGNOSE Water SOFTENER PROBLEMS - if your softener is non working
• HOW Water SOFTENERS / CONDITIONERS WORK
• INSTALLATION of Water SOFTENERS how this equipment should exist installed.
• REDUCE IMPACT of SOFTENER on SEPTIC nosotros provide suggestions for reducing the touch on of water softeners on septic systems. Beneath we provide the details of how to adjust and maintain a residential or light commercial water softener for proper operation.
• Table salt OR WATER INTO SEPTIC importance of using the proper settings that control water softener operation, and performing proper water softener maintenance volition assure that the water softener is effective in treating hard h2o, it will avoid wasting water, and if a private septic system is installed information technology volition significantly reduce the chances that a septic system will be damaged by flooding or by excessive salt due to water softener malfunction.
• WATER CONDITIONER / SOFTENER MANUALS
• Water SOFTENER Aligning & CONTROLS
  • 4 Bones Water SOFTENER ADJUSTMENTS
  • 6 WATER SOFTENER CONTROL SETTING DETAILS
  • RECOMMENDED SETTINGS for WATER SOFTENERS
  • WATER SOFTENER CAPACITY SETTING
  • Water SOFTENER CLOCK SETTINGS
  • WATER SOFTENER ELECTRONIC CONTROL SETTINGS
  • Water SOFTENER SALT DOSE SETTING
  • WATER SOFTENER MANUAL REGENERATION
  • WATER SOFTENER REGENERATION CYCLE DURATION
  • WATER SOFTENER REGENERATION CYCLE FREQUENCY
  • WATER SOFTENER MANUAL REGENERATION
• WATER SOFTENER CLEANING & SANITIZING
• WATER SOFTENER CONTROL BYPASS VALVE - how to put the h2o softener temporarily out of service.
• Water SOFTENER RESIN REPLACEMENT

Suggested citation for this web page

WATER SOFTENER ADJUSTMENT & CONTROLS at InspectApedia.com - online encyclopedia of edifice & environmental inspection, testing, diagnosis, repair, & trouble prevention advice.

Or see this

Alphabetize to RELATED Articles: ARTICLE INDEX to Water TREATMENT SYSTEMS

Or apply the SEARCH BOX establish below to Ask a Question or Search InspectApedia

...

Ask a Question or Search InspectApedia

Questions & answers or comments most issues with the operation of aerobic septic systems

Attempt the search box just below, or if you prefer, post a question or comment in the Comments box beneath and we will respond promptly.

Search the InspectApedia website

Note: appearance of your Comment below may be delayed: if your comment contains an paradigm, spider web link, or text that looks to the software every bit if information technology might be a web link, your posting will appear afterward it has been approved past a moderator. Apologies for the delay. Our Annotate Box is provided by Countable Web Productions countable.ca

Technical Reviewers & References

Click to Prove or Hide Citations & References

Source: https://inspectapedia.com/plumbing/Water_Softener_Settings.php

Share this post